Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers

Request Quote
All Products
Microphone Preamplifier - Stereo Output with Compressors
Series:
Model: EZ-MPA1
- Balanced Microphone Input on Rear-Panel XLR
- Switch-Selectable Phantom on Rear Panel
- Unbalanced Output on MINI or RCA Rear-Panel Jacks
- Preamp Feeds Left and Right Output Channels
- Front-Panel Compressor Enable/Disable Switch
Product Info
Tech Specs
Related Products
Documents
Accessories
The EZ-MPA1 is a microphone preamplifier with front-panel volume control and audio level metering. A front-panel switch engages an audio compressor to control overloads and clipping during high level audio bursts or peaks from the microphone. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The preamplified mic signal feeds both channels of the line output on RCA or MINI jacks. LED VU metering facilitates easy level adjustment. The EZ-MPA1 is ideal to add microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems.
- Balanced Microphone Input on Rear-Panel XLR
- Switch-Selectable Phantom on Rear Panel
- Unbalanced Output on MINI or RCA Rear-Panel Jacks
- Preamp Feeds Left and Right Output Channels
- Front-Panel Compressor Enable/Disable Switch
- Audio Compressor Controls Overloads
- Front-Panel LEVEL Control
- Dual-LED VU Meter
- Optimized for Dynamic or Condenser Mics
- Headroom Accomodates High Input Levels
- Headroom Increases with Lower Gain Settings
- Compressor Limits Clipping Over Wide Dynamic Range
- Preamplifier Signal Type - Audio
- input:: 1.2 kΩ balanced on XLR jack, mic-level, -11 dBu max.
- Level control:: Off to 50 dB gain
- Outputs (2):: -10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
- Frequency Response: 80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
- THD+N:: < 0.1% (35 Hz to 20 kHz, -50 dBu input)
- Compression:: 20 dB range, switch-selectable
- CMRR:: > 55 dB (20 to 20 kHz)
- Metering:: Dual-LED VU Meter, calibrated to -10 dBV output
- Phantom:: Switch-selectable 24 V (IEC 1938: 1996-12)
- Noise:: < -65 dB (below -10 dBV output, -50 dBu input)
- 24 Vdc power supply current:: 55 mA (idle), 80 mA (max.), 100 mA (max. with phantom)
- Case dimensions:: 5.75” (14.6 cm)W x 3” (7.6 cm)D
- Mounting size:: 1/3 rack width
- DC Voltage: 24 Volts
- Depth: 3 in
- Width: 5.75 in
- Noise: -65 dBA
- Shipping Weight: 1.60 lbs
EZ-MCP1X
- In-line Microphone Compressor
EZ-MPA2
- Dual Microphone Preamplifier - Stereo Output with Compressors
FP-MP1
- Studio Quality Mic Preamp w/ Phantom - Terminals & XLR
FP-MPA2
- Dual Mic Phantom Adapter 12, 24, 48 V - XLR
HR-MP2
- Dual Microphone Preamplifier
HR-MP2A
- Dual Microphone Preamplifier
ST-MPA24
- 24V Adjustable Dual Microphone Phantom Adapter
ST-MPA48
- 48V Fixed Dual Microphone Phantom Adapter
STM-1
- Microphone Preamplifier - 50 dB Gain
STM-2
- Adjustable Gain Mic Preamp - 35 to 65 dB Gain
STM-2X
- Switched Mic Preamp - 35 to 65 dB Gain
STM-3
- High Gain Mic Preamp - 35 to 75 dB Gain
STM-LDA3
- Studio Quality Mic Preamp with phantom - 3 Line Outputs
EZ-MPA1_INSTALLATION_MANUAL.pdf
700 kb
- Instructions
EZ-CC6
Component Chassis for 6 Increments of 1/6 Rack Width
EZ-DC2
Desktop Chassis for 1/3 Rack Width EZ Products
EZ-FP1
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6
EZ-RA6
Rack Adapter for 6 Increments of 1/6 Rack Width
EZ-SD1
Storage Drawer-1/6 Rack Width for EZ-RA6 or EZ-CC6
EZ-SD2
Storage Drawer - 1/3 Rack Width for EZ-RA6 or EZ-CC6
EZ-SMB2
Surface Mount Bezel for 1/3 Rack Width EZ Products
EZ-UCB2
Under Counter Bracket Pair for all EZ Product Widths
Component Chassis for 6 Increments of 1/6 Rack Width
EZ-DC2
Desktop Chassis for 1/3 Rack Width EZ Products
EZ-FP1
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6
EZ-RA6
Rack Adapter for 6 Increments of 1/6 Rack Width
EZ-SD1
Storage Drawer-1/6 Rack Width for EZ-RA6 or EZ-CC6
EZ-SD2
Storage Drawer - 1/3 Rack Width for EZ-RA6 or EZ-CC6
EZ-SMB2
Surface Mount Bezel for 1/3 Rack Width EZ Products
EZ-UCB2
Under Counter Bracket Pair for all EZ Product Widths
Request Quote
Suggested Products
Thank you!
Someone will be in touch with you shortly.
Contact TRITECH Communications
close

TRITECH Communications
625 Locust Street, Suite 300
Garden City, NY 11530
USA
(631) 254-4500
www.tritechcomm.com
Contact in regards to this product:
Radio Design Labs
Model: EZ-MPA1
Request more information from a dealer near you
close
Request more information from a dealer near you